Optimization of resistance spot welding process parameters on galvanised steel by using Taguchi method/

Optimization of resistance spot welding process parameters on galvanised steel by using Taguchi method/

The objectives of this research are to determine the optimum process parameters that needed to be control by using Taguchi method and to examine the spot welded galvanised steel nugget diameter

Guardat en:

Dades bibliogràfiques
Autor principal:	Jaraman, Poorani
Autor corporatiu:	Universiti Malaysia Perlis
Format:	Thesis Software eBook
Idioma:	English
Publicat:	Perlis,Malaysia School of Materials Engineering, Universiti Malaysia Perlis 2017
Matèries:	Metallurgy.
Etiquetes:	Afegir etiqueta Sense etiquetes, Sigues el primer a etiquetar aquest registre!

Ítems similars

The influence of welding parameters and corrosive environment on the joint strength of resistance spot-welded mild steel sheets
per: Ahmad Azid Tahar Ahmad Latiffi

The effect of varied welding currents and cycles on thin sheet mild steel with heat treatment process for resistance spot weld
per: Mohamed Faisol Mohamed Nor

Study effect of welding current on mechanical properties of galvanized steel sheets in resistance spotwelding
per: Muhammad Rifki Ismail

Optimisation of anodising parameter with oxalic acid for the formation of anodic aluminium oxide by using taguchi methods /
per: Nor Syammimi Binti Abu Hasan
Publicat: (2016)

The study of ultrasonic wave propagation in welded austenitic stainless steel
per: Mohd Faizal Esran

A study of dissimilar welding between mild steel and stainless steel on hardness and tensile shear test for gas tungsten arc welding (GTAW)
per: Ahmad Safwan Salim

Welding characteristics of similar and dissimilar metal welding/
per: Lim Yuan Ting
Publicat: (2016)

Surface modification of low carbon steel and alloy steel by boriding diffusion coating/
per: Asilah Bt Syed Abdul Wahab
Publicat: (2016)

Characterization on the effect of electrospinning parameters on polyacrylonitrile (Pan)/
per: Nurul Azni Binti Bakaruddin
Publicat: (2016)

Study on corrosion properties of stainless steel
per: Abang Fairol Abang Sarbini

Effect Geopolymer Coating On Mild Steel /
per: Muhammad Faiz Bin Mohd Fazill
Publicat: (2016)

Effect of Mixing Parameter on Epoxy Composites: Mechanical and Microscopy Analysis /
per: Ng, Soo Li
Publicat: (2017)

The Effect Of Iron Addition And Tungsten Content On The Corrosion Resistance Of W-Pre Alloy Brass Composite/
per: Rozi Bin Ewol
Publicat: (2016)

Study the mechanical properties and microstructure on steel products
per: Khairul Nizam Hashim

The effect of alloying elements in sintered-recycle steel compaction
per: Mohd Fauzi Jaafar

Developing a mold technology module for freescale - study on effects of materials (compound properties) and molding process parameters on package moldability for QFP
per: Tan, Hui Khin

Controlling the synthesis parameter during fe(OH)2 precipitation for goethite formation /
per: Noraishah Binti Mohamed Noor
Publicat: (2016)

The effect of different particle size of steel slag as filler in concrete/
per: Ellisha Anak Iling
Publicat: (2016)

Direct growth of Cnms on stainless steel (effect of surface roughness)/
per: Muhammad Izzhar Abd Malik
Publicat: (2016)

Study on the effect of reinforcement particle size parameter on aluminum metal matrix composite reinforced with alumina particles
per: Salihah Tan Shilan

Treatise on process metallurgy /
Publicat: (2014)

A study on corrosion behavior of mild steel in Granulated Blast Furnace (GBFS) fly ash geopolmer /
per: Siti Farahnabilah Muhd Amli
Publicat: (2017)

Effects of volume fraction and particle size reinforcement parameter to microstructure and thermal properties of copper silicon carbide (CuSiC) composite for electronic pakaging application
per: Siti Amira Faisha Shikh Zakaria

The process of electroplating in presence of nickel salts
per: Mohd Saiful Khairuddin Azahar

The processing of pegmatitle ore the extraction of feldspar and silica/
per: Nor 'Ain Binti Yusah
Publicat: (2016)

Anodizing process of Mg alloy using low potential /
per: Siti Auni Shafiqah Makhtar
Publicat: (2017)

Synthesis and Characterization of Ternary Glass Composition Derived by sol-gel Method /
per: Nik Nur Syahirah Nik Suhaimi
Publicat: (2017)

Synthesis and Characterization of Alumina Nanoparticles by using a Sol Gel Method /
per: Siti Nur Syakirah Binti Mohamad
Publicat: (2017)

Study of fabrication AI-Tin slag composite by powder metallurgy method
per: Muhammad Syazwan Abdul Manan

Study the different sintering temperature for Fe-11wt%Co/20wt%SiC composite an the composite will be fabricated via powder metallury method consists of mixing, compation and sintering processes
per: Durairaj Ehambron

Optimisation of z - blade compounding process for enhanced composite performance /
per: Siti Jamilah Binti Mohd Ariff
Publicat: (2016)

The study of silver coated immobilized pani/tio2 by using photo-oxidation method /
per: Nurul Dasira Binti Ismail
Publicat: (2016)

Study On The Microstructure and Properties of Al-Zn Alloy Fabricated By Sand Casting Process /
per: Syed Mohd Fikri Syed Sulaiman
Publicat: (2017)

Effects of ultrasonication process to morphology and tear strength of thermoplastic starch/cellulose biocomposite/
per: V. Thiviya A/P P.Vijayarajah
Publicat: (2016)

Effect of Winding Angles on The Epoxy/Kenaf/Glass Fiber Hybrid Composite by Filament Winding Process /
per: Mahtumah Honani
Publicat: (2017)

Synthesis of chlorophyll thin film from hibiscus leaves by dip coating sol-gel process/
per: Muhammad Syafie Bin Ahmad
Publicat: (2016)

Synthesis and characterization of TiO2 USING SOL-GEL method deposited on Porous Cordierite for water treatment application/
per: Ong, Yong Por
Publicat: (2017)

Synthesis of chlorophyll thin film from euphoria malaiense leaves by using dip coating sol-gel process/
per: Rizwan Husri Bin Roslan
Publicat: (2016)

Effects of high weight percent of space holder on porosity and microstructure of aluminum foam manufacturated by sintering-dissolution process (sdp) /
per: Nur Hazwani Mohd Yusoff
Publicat: (2016)

Effect of particle size and milling process on the microstructure and thermal properties of copper silicon carbide (CuSiC) composites for electronic packing application
per: Chuah, Run Yi