Study of the effect of different gases parameter in dry etching process on etch rate profile

The principal focus of this project is dry etching technique by using the Inductively Couple Plasma -Reactive Ion Etching (ICP-RIE). This final year project is about to understand and control the equipment for dry etches process. The equipment in dry etch process is inductively couple plasma- reacti...

Descripció completa

Guardat en:

Dades bibliogràfiques
Autor principal:	Zaharah Mohamad (Autor)
Format:	Electrònic Software Base de dades
Idioma:	English
Matèries:	Microelectronics.
Etiquetes:	Afegir etiqueta Sense etiquetes, Sigues el primer a etiquetar aquest registre!

Ítems similars

Reactive ion etching (RIE) etched wet-silica-on-silicon analysis for fluidwettability
per: Noor Aini Hamimah Abd. Rahim

Study of aspect ratio performance on silicon oxide etching using profiler meter, AFM and SEM
per: Nur Syuhada Md. Desa

Comparison of etching optimization process by taguchi method using minitab and design expert software
per: Azleen Abu Talib

Dry Etching Technology for Semiconductors /
per: Nojiri, Kazuo
Publicat: (2015)

Design and fabricate "wineglass" contact formation by simultaneous wet-dry etch process.
per: Mohd Norhafiz Bin. Hashim

Polysilicon process development - the effect of pecvd process parameters on the film characteristics
per: Mujahidun Mashuri

The study of the effect of MOS transistor scaling on the critical device parameters
per: Zazurina Abd Rahman

Study of the thickness of the silicon dioxide on wafer using dry and wet oxidation method
per: Mohamad Fadzli Ali

The effect of process parameters on metal step coverage for aluminum (AI) by evaporation technique
per: Noraishah Azman

Ultra violet scanner, PCB developer and etching machine
per: Nur Bazilah Mohd Suhaimi
Publicat: (2010)

Ultra violet scanner, PCB developer and etching machine
per: Nur Bazilah Mohd Suhaimi
Publicat: (2010)

Effect of different dielectric materials for ultrathin oxide
per: Zarimawaty Zailan

Portable etching machine/
per: Julasri Ragiman
Publicat: (2018)

Etching & microscopy 09
Publicat: (2009)

Portable etching machine /
per: Muhammad Azlan Shah Ibrahim
Publicat: (2015)

Etching & microscopy 09
Publicat: (2009)

Portable etching machine /
per: Muhammad Azlan Shah Ibrahim
Publicat: (2015)

Study the effect of bird's beak on fully recessed locos and poly buffered locos using 2 different pad oxide
per: Hafizal Hafiz Sarjoni

Theoretical study, simulation & fabrication on dry oxidation in terms of Si02 layer thinckness, resistivity & surface roughness
per: Mohd Adam Alias

Simulation on effect of different types of channel/ drain engineering structure on MOS device performance
per: Norazlina Mohd Amin

Level 1 parameter extraction of MOSFET device
per: Azman mat Hussin

Study of the temperature effect on thickness and surface roughness of Si02
per: Mohd Azdi Asis

Study the effect of environmental noise on infrared Tx-Rx circuit signals
per: Mohd Zaihan Ibrahim

Simulation on parameter and characteristics extraction between two simulation packages (synopsys and pspice)
per: Nor Aznin Sakrani

Nanostructure formation using sem based e-beam lithography (EBL) technique : buffered oxide etch (BOE) profile
per: Nur Nazihah Halemi

The study on the effect of varing dopant concentration and diffusion time in the design of silicon avalanche diode with minimum VBR of 120+-20%
per: Yip, Siew Ling

Study of semi-recessed LOCOS for quasi-nanoscale CMOS devise isolation
per: Mohamad Idzham Abd Sani

Study of deposition time influence the conical structure during electron beam induced deposition (EBID)
per: Mohamad Shahrizal Md Ilias

Study and design infrared beacon for the blind
per: Mohd Fadzlie Rasit

Thin polycrystalline silicon process development
per: Muniyati Pakhuruddin

Study and improvement of UniMAP shower room
per: Lau, Iyu Pin

The effect of power density on the surface layer of amorphous thin film
per: Ahmad Fadzil Izaharuddin

Effect of diffusion coefficient and junction depth on variation of temperature and energy
per: Nur Ruzana Bohari

Optimization of nitride deposition process using Taguchi method
per: Low, Zen Shiang

Semiconductor optical amplifier (SOA) for photonic signal processing/
per: Latty Shazana Ismail
Publicat: (2011)

Area array packaging processes : for BGA, flip chip and CSP /
Publicat: (2004)

Area array packaging processes : for BGA, Flip Chip, and CSP /

Study the basic infrared tx-rx circuit design for robot
per: Nik Ahmad Faiz Abdul Jamel

Fabrication of 50 ¡Łm transistor and AINiAu interconnection process
per: Shaffie Husin

Optimization on oxidation process using 2K factorial design method
per: Yeap, Li Chain