Study on single strut formation using additive layer manufacturing /

Study on single strut formation using additive layer manufacturing /

Mostrar otras versiones (1)

Guardado en:

Detalles Bibliográficos
Autor principal:	Chee, Ying Chen (Autor)
Formato:	Software eBook
Lenguaje:	English
Publicado:	2018.
Materias:	Three-dimensional printing. Structural design.
Etiquetas:	Agregar Etiqueta Sin Etiquetas, Sea el primero en etiquetar este registro!

Ejemplares similares

Study on single strut formation using additive layer manufacturing /
por: Chee, Ying Chen
Publicado: (2018)

Study on lattice-structure node formation using additive layer manufacturing /
por: Jannatul Al-Qashah Muhd Ali Jinnah
Publicado: (2018)

Study on lattice-structure node formation using additive layer manufacturing /
por: Jannatul Al-Qashah Muhd Ali Jinnah
Publicado: (2018)

Effect of node enhancement on strength of body-centered-cubic (BCC) polymer lattice-structure material /
por: Ahmad Wahi Ab.Rahman
Publicado: (2018)

Effect of node enhancement on strength of body-centered-cubic (BCC) polymer lattice-structure material /
por: Ahmad Wahi Ab.Rahman
Publicado: (2018)

Effects of process parameters on strength of polymer lattice structure manufactured by using 3D printer
por: Ng, Wai Hoe
Publicado: (2017)

Effects of process parameters on strength of polymer lattice structure manufactured by using 3D printer
por: Ng, Wai Hoe
Publicado: (2017)

Investigation on similarities between 3D-printed single strut and struts in lattice- structure arrangement /
por: Muhammad Shahril Afzan Jailani
Publicado: (2019)

Investigation on similarities between 3D-printed single strut and struts in lattice- structure arrangement /
por: Muhammad Shahril Afzan Jailani
Publicado: (2019)

Layer adhesion investigation of 3D printer platform /
por: Nornarieyza Rosli
Publicado: (2017)

Layer adhesion investigation of 3D printer platform /
por: Nornarieyza Rosli
Publicado: (2017)

Investigation on process-properties relationship with load-bearing performance of lattice-structured cellular material for lightweight applications /
por: Rafidah Hasan, Dr, et al.
Publicado: (2019)

Investigation on process-properties relationship with load-bearing performance of lattice-structured cellular material for lightweight applications /
por: Rafidah Hasan, Dr, et al.
Publicado: (2019)

Understanding additive manufacturing
por: Gebhardt, Andreas
Publicado: (2012)

Understanding additive manufacturing
por: Gebhardt, Andreas
Publicado: (2012)

Analysis on components produced using wire arc additive manufacturing /
por: Fatin Nazirah Binti Ismail
Publicado: (2019)

Analysis on components produced using wire arc additive manufacturing /
por: Fatin Nazirah Binti Ismail
Publicado: (2019)

3D printing technology, applications, and selection
por: Noorani, Rafiq
Publicado: (2018)

3D printing technology, applications, and selection
por: Noorani, Rafiq
Publicado: (2018)

Friction based additive manufacturing technologies : principles for building in solid state, benefits, limitations, and applications /
por: Rathee, Sandeep, et al.
Publicado: (2018)

Friction based additive manufacturing technologies : principles for building in solid state, benefits, limitations, and applications /
por: Rathee, Sandeep, et al.
Publicado: (2018)

Design and manufacturing of protective mask : modeling and fabrication of low-cost device using additive manufacturing technology /
por: Ahmad Afiq Baharuddin
Publicado: (2018)

Design and manufacturing of protective mask : modeling and fabrication of low-cost device using additive manufacturing technology /
por: Ahmad Afiq Baharuddin
Publicado: (2018)

A study on selective laser sintering behaviour and processing of polymer powder mixtures /
por: Ng, Rui Ying
Publicado: (2019)

A study on selective laser sintering behaviour and processing of polymer powder mixtures /
por: Ng, Rui Ying
Publicado: (2019)

Feasibility study of dental crown manufacturing by using rapid prototyping and CNC technology towards digital dental manufacturing /
por: Wan Nur Amirah Wan Muhamad
Publicado: (2019)

Feasibility study of dental crown manufacturing by using rapid prototyping and CNC technology towards digital dental manufacturing /
por: Wan Nur Amirah Wan Muhamad
Publicado: (2019)

Effect of layer thickness and fill angle on flexural properties of carbon fibre reinforced ABS printed part /
por: Amirah Diyana Ahmad Azan
Publicado: (2017)

Effect of layer thickness and fill angle on flexural properties of carbon fibre reinforced ABS printed part /
por: Amirah Diyana Ahmad Azan
Publicado: (2017)

Thermal behavior of additve manufacturing process
por: Muhammad Fayyadh Izzat Azmi
Publicado: (2015)

Thermal behavior of additve manufacturing process
por: Muhammad Fayyadh Izzat Azmi
Publicado: (2015)

3D printing and additive manufacturing : principles and applications /
por: Chua, Chee Kai, et al.
Publicado: (2017)

3D printing and additive manufacturing : principles and applications /
por: Chua, Chee Kai, et al.
Publicado: (2017)

Comparative study of additive manufacturing on intricate part /
por: Nur Syahirah Nabihah Muhammad Nor
Publicado: (2019)

Comparative study of additive manufacturing on intricate part /
por: Nur Syahirah Nabihah Muhammad Nor
Publicado: (2019)

Additive manufacturing in medical application, a comparative study between conventionally made prosthesis (pylon) and fused deposition modelling prosthesis (pylon)
por: Mohammad Aizrulshah Kamaruddin
Publicado: (2017)

Additive manufacturing in medical application, a comparative study between conventionally made prosthesis (pylon) and fused deposition modelling prosthesis (pylon)
por: Mohammad Aizrulshah Kamaruddin
Publicado: (2017)

Investigation on mechanical and thermal properties of 100% recycled 3D printed ABS material /
por: Anis Hazirah Samat
Publicado: (2019)

Investigation on mechanical and thermal properties of 100% recycled 3D printed ABS material /
por: Anis Hazirah Samat
Publicado: (2019)

Surface pressure distribution of 3D printed ball bearing with internal structure formation using CAE /
por: Muhammad Zulhimi Nordin
Publicado: (2019)