Design a non-electrical table fan

Design a non-electrical table fan

Veure altres versions (3)

Guardat en:

Dades bibliogràfiques
Autor principal:	Nor Ayu Mohamad Norani (Autor)
Autor corporatiu:	Universiti Teknikal Malaysia Melaka. Faculty of Mechanical Enginering (institution)
Format:	Thesis Llibre
Idioma:	English
Publicat:	2018
Matèries:	Concurrent engineering. Product design. Fans.
Etiquetes:	Afegir etiqueta Sense etiquetes, Sigues el primer a etiquetar aquest registre!

Ítems similars

Design a non-electrical table fan
per: Nor Ayu Mohamad Norani
Publicat: (2018)

Design a non-electrical table fan
per: Nor Ayu Mohamad Norani
Publicat: (2018)

Design a non-electrical table fan
per: Nor Ayu Mohamad Norani
Publicat: (2018)

Design a low cost table fan using DFMA analysis /
per: Nurul Farmira Zakaria
Publicat: (2016)

Design a low cost table fan using DFMA analysis /
per: Nurul Farmira Zakaria
Publicat: (2016)

Rekabentuk kipas penyejuk segar
per: Azrul Hiza Muhamad Azraai
Publicat: (2007)

Rekabentuk kipas penyejuk segar
per: Azrul Hiza Muhamad Azraai
Publicat: (2007)

Concurrent decisions on design concept and material using analytical hierarchy process at the conceptual design stage
Publicat: (2011)

Concurrent decisions on design concept and material using analytical hierarchy process at the conceptual design stage
Publicat: (2011)

Redesign of a product using boothroyd DFA approach /
per: Nurul Ain Ismail
Publicat: (2009)

Redesign of a product using boothroyd DFA approach /
per: Nurul Ain Ismail
Publicat: (2009)

Productivity analysis of table top fan assembly process using arena simulation /
per: Mohd Norhaffiz Noor Aini
Publicat: (2009)

Productivity analysis of table top fan assembly process using arena simulation /
per: Mohd Norhaffiz Noor Aini
Publicat: (2009)

Product design optimization using design for manufacture and assembly /
per: Nurul Fahana Zizam
Publicat: (2018)

Product design optimization using design for manufacture and assembly /
per: Nurul Fahana Zizam
Publicat: (2018)

Product design optimization using design for manufacture and assembly approaches
per: Tengku Mohd Saalahuddin Tengku Nordin
Publicat: (2008)

Product design optimization using design for manufacture and assembly approaches
per: Tengku Mohd Saalahuddin Tengku Nordin
Publicat: (2008)

Product design for manufacture and assembly
per: Boothroyd, Geoffrey
Publicat: (2002)

Product design for manufacture and assembly
per: Boothroyd, Geoffrey
Publicat: (2002)

Product design for manufacture and assembly /
per: Boothroyd, Geoffrey, et al.
Publicat: (2011)

Product design for manufacture and assembly /
per: Boothroyd, Geoffrey, et al.
Publicat: (2011)

Simultaneous engineering methodologies and applications

Implementing concurrent engineering in small companies
per: Skalak, Susan Carlson
Publicat: (2002)

Simultaneous engineering methodologies and applications

Implementing concurrent engineering in small companies
per: Skalak, Susan Carlson
Publicat: (2002)

The application of time compression technologies of an artifact in Malay carving (mould of 'Papan Pemanis') /
per: Mohammad Syafiq Mohd Sarif
Publicat: (2015)

The application of time compression technologies of an artifact in Malay carving (mould of 'Papan Pemanis') /
per: Mohammad Syafiq Mohd Sarif
Publicat: (2015)

Design and fabrication of bollard light using modern product development process
per: Farhani Mohamad
Publicat: (2008)

Design and fabrication of bollard light using modern product development process
per: Farhani Mohamad
Publicat: (2008)

The adoption of simultaneous engineering (SE) in design-manufacturing interface in automotive new product introduction (NPI) /
per: Nur Nadia Atiqah Mohamad Dzuhaimin
Publicat: (2015)

The adoption of simultaneous engineering (SE) in design-manufacturing interface in automotive new product introduction (NPI) /
per: Nur Nadia Atiqah Mohamad Dzuhaimin
Publicat: (2015)

Enhancement and performance analysis of design for assembly methodology
per: Zulkeflee Abdullah
Publicat: (2006)

Enhancement and performance analysis of design for assembly methodology
per: Zulkeflee Abdullah
Publicat: (2006)

Design and product development of iPod casing through concurrent engineering tools and technology /
per: Marlia Rassim
Publicat: (2009)

Design and product development of iPod casing through concurrent engineering tools and technology /
per: Marlia Rassim
Publicat: (2009)

Design and product development of product(s) through concurrent engineering tools and methodology
per: Mohd Aizuddin Abd Razak
Publicat: (2009)

Design and product development of product(s) through concurrent engineering tools and methodology
per: Mohd Aizuddin Abd Razak
Publicat: (2009)

Design and development of plastic injection mould with concurrent engineering
per: Chai, Jivan Hua
Publicat: (2008)

Design and development of plastic injection mould with concurrent engineering
per: Chai, Jivan Hua
Publicat: (2008)

Product improvement of Cornell CFF-12P fan by design for assembly method (Boothroyd Dewhurst) /
per: Siti Azureen Sapardin
Publicat: (2016)