Milling of inconel 718 by using uncoated WC-Co insert in the dry condition /

Milling of inconel 718 by using uncoated WC-Co insert in the dry condition /

Veure altres versions (1)

Guardat en:

Dades bibliogràfiques
Autor principal:	Mohd Aratah Abdul Latif (Autor)
Autor corporatiu:	Kolej Universiti Teknologi Tun Hussein Onn. Fakulti Kejuruteraan Mekanikal dan Pembuatan
Format:	Thesis Llibre
Idioma:	Malay
Publicat:	Batu Pahat : Kolej Universiti Teknolpgi Tun Hussein Onn, 2006.
Matèries:	Metal-cutting. Metal-cutting tools. Inconel.
Etiquetes:	Afegir etiqueta Sense etiquetes, Sigues el primer a etiquetar aquest registre!

Ítems similars

Milling of inconel 718 by using uncoated WC-Co insert in the dry condition /
per: Mohd Aratah Abdul Latif
Publicat: (2006)

A study on the performance of WC-Co uncoated when endmill inconel 718 in dry condition /
per: Mohd Noor Hairil Mohd Yusof
Publicat: (2006)

Study of vibration and surface roughness in milling inconel 718 with TiAIN coated in dry condition /
per: Mohd Affendi Kamsin
Publicat: (2006)

Study of cutting force and tool wear in end milling inconel 718 with coated carbride inserts in dry condition /
per: Ashrul Riezal Asbar
Publicat: (2006)

Investigation on machining microholes on inconel 718 by EDM /
per: Muhammad Danial Muhammad Masri
Publicat: (2006)

Investigation of surface integrity when using micro EDM inconel 718 /
per: Abu Al Itqan Ismail
Publicat: (2007)

Micro-hole drilling edm of inconel 718 by using copper tungsten elecrode /
per: Said Ahmad
Publicat: (2006)

A study on the performance of WC-Co uncoated when endmill inconel 718 in dry condition /
per: Mohd Noor Hairil Mohd Yusof
Publicat: (2006)

Chip formation when milling inconel 718 /
per: Wan Basriyah Abdul Rahman
Publicat: (2014)

The effect of TiAIN and TiN coating when milling inconel 718/
per: Roslan Aziz
Publicat: (2010)

Optimization of end milling on inconel 718 using Tiain coated carbide /
per: Ahmad Sabree Abdul Basit
Publicat: (2018)

Study of vibration and surface roughness in milling inconel 718 with TiAIN coated in dry condition /
per: Mohd Affendi Kamsin
Publicat: (2006)

Study effect of chip and vibration when milling inconel 718 using TiN and TiAIN coated carbide /
per: Muhamad Aimran Suhaimi
Publicat: (2010)

Kajian pengaruh tindakan daya pemotongan terhadap kekasaran permukaan bahan kerja (mild steel) /
per: Mohd Suhizan Siman
Publicat: (2003)

Measurement of cutting tool temperature in high spees machining of cast iron /
per: Ahmad Hanbali Abidin
Publicat: (2006)

Kajian dalam menentukan parameter optimum dalam proses melarik permukaan berkualiti /
per: Muhamad Shariff Jainal
Publicat: (2006)

Hubungan antara parameter pemesinan dan daya pemotongan terhadap keluli keras /
per: Mohd Shahrizal Che Mat
Publicat: (2006)

Cutting forces on a case hardened material /
per: Marimuthu, Mageswari
Publicat: (2005)

Study on surface integrity when EDM titanium using graphite electrode /
per: Too, Heng Chee
Publicat: (2006)

Metal cutting /
per: Trent, E. M.
Publicat: (2000)

Performance of wc-co tools when milling titanium alloys (Ti-6AI-4V) /
per: Mohd Faizal Azmi
Publicat: (2006)

Performance of TiCN coated tool in machining (end milling) hardened steel /
per: Choo, Woon Chik
Publicat: (2006)

Evaluation of flank wear and surface roughness when miling titanium alloy (TI-6A1-4V) using coated and uncoated carbide insert /
per: Zulkarnain Ramli
Publicat: (2006)

Analisis hubungan di antara daya pemotongan, kekasaran permukaan dan sudut ricihan dalam operasi melarik /
per: Ahmad Zia Mhd Yusof
Publicat: (2004)

Prestasi mata alat tanpa salut karbida selepas penggerudian aloi titanium /
per: Khairul Nizam Kamarudin
Publicat: (2005)

Study of cutting force and tool wear in end milling inconel 718 with coated carbride inserts in dry condition /
per: Ashrul Riezal Asbar
Publicat: (2006)

Investigation on machining microholes on inconel 718 by EDM /
per: Muhammad Danial Muhammad Masri
Publicat: (2006)

Study of surface integrity of titanium alloy in wire electrical discharge machining /
per: Chin, Wei Ping
Publicat: (2006)

A development of recycled-electrode in electrical discharge machining (EDM) of aluminium alloy 6061 - A preliminary study /
per: Mohd Firdaus Zakaria
Publicat: (2014)

Effect on TiN coating on surface integrity of elelctrical discharge machined tool steel /
per: Khairi Azhar Hashim
Publicat: (2010)

Advanced machining processes of metallic materials : theory, modelling and applications /
per: Grzesik, Wit
Publicat: (2008)

Investigation of surface integrity when using micro EDM inconel 718 /
per: Abu Al Itqan Ismail
Publicat: (2007)

Kajian tehadap pengaruh tindakan daya pemotongan pada kehausan dan hayat mata alat /
per: Mohd Sani Ahmad
Publicat: (2002)

Metal cutting principles /
per: Shaw, Milton Clayton
Publicat: (2005)

Metal cutting theory and practice /
per: Stephenson, David A.
Publicat: (2005)

Metal cutting mechanics /
per: Astakhov, Viktor P.
Publicat: (1999)

Micro-hole drilling edm of inconel 718 by using copper tungsten elecrode /
per: Said Ahmad
Publicat: (2006)

Surface integrity in laser assisted micro milling (LAMM) of inconel 718 /
per: Muhammad Azzie Adireezzal Azhar
Publicat: (2015)

Pembentukan tatal dan daya pemotongan dalam proses penggerudian bagi aloi titanium /
per: Mohd Fahme Muhamad
Publicat: (2006)

To investigate the effect of cutting parameter when machining inconel 718 using end milling /
per: Mohammad Ikhram Mohammad Nasikin
Publicat: (2013)