Study On The Microstructure and Properties of Al-Zn Alloy Fabricated By Sand Casting Process /

Study On The Microstructure and Properties of Al-Zn Alloy Fabricated By Sand Casting Process /

The objectives of this research are to perform sand casting process with different Zn composition on Al based alloy, to study the microstructure of as-cast Al-Zn casting alloys and to study the mechanical properties of as-cast Al-Zn casting alloys.

Guardat en:

Dades bibliogràfiques
Autor principal:	Syed Mohd Fikri Syed Sulaiman
Autor corporatiu:	Universiti Malaysia Perlis
Format:	Thesis Software eBook
Idioma:	English
Publicat:	Perlis,Malaysia School of Materials Engineering, Universiti Malaysia Perlis 2017
Matèries:	Metallurgy.
Etiquetes:	Afegir etiqueta Sense etiquetes, Sigues el primer a etiquetar aquest registre!

Ítems similars

Microstructural and thermal studies of as-cast al-si-mg alloys
per: Lokman Hakim Ibrahim

Effects of T6 treatment on the microstructural changes, hardness and thermal analysis of As-Cast Al-Si-Mg alloys
per: Izrul Azree Mohd Zaki

Study the mechanical properties and microstructure on steel products
per: Khairul Nizam Hashim

Fabrication of Al-based Metallic Glasses by Mechanical Alloying and Hot Consolidation /
per: Ng, Chun Ming
Publicat: (2017)

Characterization of casting alloy Al 319 (Al-12Si-4Cu-0.1Mg), PROTON cylinder head
per: Khairul Khusairi Kamaludin

The fabrication of porcelain ceramic via wet casting technique
per: Meor Syazalee @ Meor Sha

A study of microstructure and mechanical properties of copper filled polypropylene and copper filled epoxy
per: Nor Riza Kamalul Baharim

Effect of solution treatment temperature on the microstructure of fe-40ni-24cr alloy /
per: Nuraliah Nazirah Mohd Hassan
Publicat: (2016)

Synthesis and mechanical properties of alumina slip casting from aluminium tri- hydrate (aL(oh)3)/
per: Nurfarahin Binti Mohd. Nordin
Publicat: (2016)

Development of Al-Ni-Cu Amorphous Alloy Powder /
per: Norliyana Mustapar
Publicat: (2017)

The properties and photocatalytic behaviour of TiO2 and ZnO particles after modification with PVP and ag nanoparticles/
per: Mohd Faidhiradhi Mohd Fazuki
Publicat: (2016)

The effect of cooling condition on the microstructure and properties of Al-4.4Cu-0.8Si-0.5Mg powder compacts
per: Khairul Nazri Taha

Synthesis and characterization of fe-al alloy with different sintering temperature
per: Maimum Razali

Surface modification of low carbon steel and alloy steel by boriding diffusion coating/
per: Asilah Bt Syed Abdul Wahab
Publicat: (2016)

Microstructure development of Al-Mg-Si-Cu powder metallurgy under different addition of Sn
per: Khairunnisa Omar

Sintering behavior and microstructural characterization of aluminium copper powder compact (al-4.4cu-0.8si-0.5mgwt%) alloy prepared by powder metallurgy
per: Looi, Mei Yen

Anodizing process of Mg alloy using low potential /
per: Siti Auni Shafiqah Makhtar
Publicat: (2017)

Effect of particle size and milling process on the microstructure and thermal properties of copper silicon carbide (CuSiC) composites for electronic packing application
per: Chuah, Run Yi

Study on corrosion properties of stainless steel
per: Abang Fairol Abang Sarbini

Electroplating Copper on Aluminium Alloy/
per: Nurhafizah Binti Ku Abdullah
Publicat: (2016)

Study on properties of molybdenum filled polypropylene composites
per: Junizah Abdul Rashid

Recovery of copper (Cu) from printed circuit board (PCB) using lakos separator
per: Syed Aqil Syed Nadzir

Study of fabrication AI-Tin slag composite by powder metallurgy method
per: Muhammad Syazwan Abdul Manan

Effect of corrosion in acidic solution to the phase and microstructure of sn-cu solder/
per: Gan, Zhi Wan
Publicat: (2016)

Effect of corrosion in acidic solution to the phase and microstructure of sac305 solder /
per: Khoo, Cheng Hao
Publicat: (2016)

Effects of high weight percent of space holder on porosity and microstructure of aluminum foam manufacturated by sintering-dissolution process (sdp) /
per: Nur Hazwani Mohd Yusoff
Publicat: (2016)

The anodizing of sintered mg/ca alloys/
per: Norhadira Fatin Binti Wardi
Publicat: (2016)

The study of mechanical and thermoelectric properties of nickel zinc ferrite /
per: Noor Amalina Binti Mat Zin
Publicat: (2016)

Physical properties of Ti1-XMXAl intermetallic alloy (M = La, Ce; X = 0.25, 0.5) /
per: Muhammad Afiq Bin Mohd Razak
Publicat: (2016)

Properties of chitosan/halloysite nanotubes composite films /
per: Syahira Adila Binti Mat Sulaiman
Publicat: (2016)

Study on properties of sugarcane bagasse fiber filled polypropylene composites
per: Nur Sheli Akma Ramli

Effects of volume fraction and particle size reinforcement parameter to microstructure and thermal properties of copper silicon carbide (CuSiC) composite for electronic pakaging application
per: Siti Amira Faisha Shikh Zakaria

Fabrication and characterization of porcelain ceramic tiles
per: Shamini Muniandy

Mechanical properties of copper ferrite cufe2o4-polymer composite fabricated using 3d printer/
per: Lee, Chye Heng
Publicat: (2016)

The effect of alloying elements in sintered-recycle steel compaction
per: Mohd Fauzi Jaafar

Modelling aging kinetics of aluminium alloy aa2124/
per: Tiaw, Wei Ping
Publicat: (2016)

Modelling aging kinetics of aluminium alloy AA2124/
per: Mohamad Zulhilmi Bin Md Nasir
Publicat: (2016)

Developing a mold technology module for freescale - study on effects of materials (compound properties) and molding process parameters on package moldability for QFP
per: Tan, Hui Khin

Sintering atmosphere effect on AI-0.2mg alloy
per: Muhammad Firdaus Rosli

Effect of dopant ionic size on room temperature thermoelectric properties of YbAl3M (M = Be, Si, Ga, In) /
per: Qurratu Aini Aishah Binti Ahmad Fazil
Publicat: (2016)